OMAL
Namur interface double acting pneumatic actuator
The new and updated Omal aluminium standard double acting pneumatic actuator - now with an integrated NAMUR interface and adjustable end of travel stops - from DAN15 and bigger, to 8,000Nm.
Torque output from 8Nm to 8,000Nm (only from 15Nm with integrated NAMUR interface). Torque is directly proportional to the air supply (see table on spec sheet). 8Nm to 60Nm available to purchase directly online, over 60Nm requires ordering via our Technical Sales Engineers.
ISO Mounting flange according to EN ISO 5211. ISO: F03 - F04 - F05 - F07 - F10 - F12 - F14 - F16 - F25.
Energized and self-lubricated strips. Less friction between piston and cylinder. It prevents the bonding of the seal to the cylinder even after long periods of inactivity.
Slots, bushes and pins made by steel with hardness higher than 50 HRC. Higher resistance to the forces inside the actuator.
Rolling friction between piston and slot also mean less friction with consequently less wear on the relevant parts.
Scotch yoke design (transforming rotary motion into linear motion using piston and shaft without teeths/gears). Smaller volume/size and less weight than rack and pinion actuators (with the same torque) therefore less space required for installation and consequent savings on the construction sizing of the plant/equipment. Lower air consumption compared to the rack and pinion actuators (-40% air cm3/Nm for Double Acting and -20% air cm3/Nm for Spring Return) therefore less load on the compressor or the possibility of using a smaller compressor's size.
- Rolled cylinder. Less wear of the energized ties thanks to the low roughness of the surface (0.15 micron Ra).
- In accordance with EN 15714-3
- Rotation angle 92° (-1°, +91°C)
- ATEX version in conformity with directive 2014/34/EU - Available on request
- SIL 3 Certified
- Temperature: from 0°C to +80°C; from -20°C to +80°C with dry air only. (High Temperature -20°C, +150°C ; Low Temperature -50°C, +60°C special execution)
- Air supply: 5,6 bar; maximum 8,4 bar (7 bar for DA8000)
- Operating media: compressed filtered air, not necessarily lubricated. (In case of lubricated air, either non detergent oil or NBR compatible oil, must be used.)
- Torque output 8Nm to 8000Nm
- Air supply 5,6 bar; maximum 8,4 bar
- Temperatue range 0°C to +80°C
- ATEX available on request
Selected variant
OMAL double acting pneumatic actuator, namur interface - Part numbers coming soon, contact us for more information
Art:
Selected variant
Specifications
Downloads
Product description
The new and updated Omal aluminium standard double acting pneumatic actuator - now with an integrated NAMUR interface and adjustable end of travel stops - from DAN15 and bigger, to 8,000Nm.
Torque output from 8Nm to 8,000Nm (only from 15Nm with integrated NAMUR interface). Torque is directly proportional to the air supply (see table on spec sheet). 8Nm to 60Nm available to purchase directly online, over 60Nm requires ordering via our Technical Sales Engineers.
ISO Mounting flange according to EN ISO 5211. ISO: F03 - F04 - F05 - F07 - F10 - F12 - F14 - F16 - F25.
Energized and self-lubricated strips. Less friction between piston and cylinder. It prevents the bonding of the seal to the cylinder even after long periods of inactivity.
Slots, bushes and pins made by steel with hardness higher than 50 HRC. Higher resistance to the forces inside the actuator.
Rolling friction between piston and slot also mean less friction with consequently less wear on the relevant parts.
Scotch yoke design (transforming rotary motion into linear motion using piston and shaft without teeths/gears). Smaller volume/size and less weight than rack and pinion actuators (with the same torque) therefore less space required for installation and consequent savings on the construction sizing of the plant/equipment. Lower air consumption compared to the rack and pinion actuators (-40% air cm3/Nm for Double Acting and -20% air cm3/Nm for Spring Return) therefore less load on the compressor or the possibility of using a smaller compressor's size.
- Rolled cylinder. Less wear of the energized ties thanks to the low roughness of the surface (0.15 micron Ra).
- In accordance with EN 15714-3
- Rotation angle 92° (-1°, +91°C)
- ATEX version in conformity with directive 2014/34/EU - Available on request
- SIL 3 Certified
- Temperature: from 0°C to +80°C; from -20°C to +80°C with dry air only. (High Temperature -20°C, +150°C ; Low Temperature -50°C, +60°C special execution)
- Air supply: 5,6 bar; maximum 8,4 bar (7 bar for DA8000)
- Operating media: compressed filtered air, not necessarily lubricated. (In case of lubricated air, either non detergent oil or NBR compatible oil, must be used.)
Ordering information
Please refer to the datasheet under 'downloads' for part numbers and/or technical data, we are working on getting all part numbers and technical data on the website as soon as possible.
Tekox Terminal Strips Safety Blocks and Porcelain Blocks
Great electrical installations don't fail because of the major components. They fail because of the small ones that didn't get enough attention.
It's easy to focus on the big-ticket items during specification — and let the terminal blocks become an afterthought. But inferior connection components have a habit of making themselves known over time. Loose connections, degraded insulation, premature failure. The kind of faults that are frustrating to trace and expensive to fix.
Tekox engineer their terminal strips, safety blocks, insulated strips, and porcelain blocks to the standards your installations deserve. Available now from Demesne Electrical — get in touch and we'll show you the range.
Conta-Clip Push-in PPVK Distribution Terminals
Conta-Clip PPVK push-in potential distribution terminals simplify control cabinet wiring with tool-free connections, compact DIN rail mounting, and reliable current distribution up to 41A.
.png?as=1&iar=0&hash=6DDD16B03C4B424998A14DE19FF641F1)
Electrical Protection in Energy Storage Systems (ESS): Keys to a Safe Installation
The PMX fuse holder range is compact, halogen-free, and manufactured in Europe for fast availability. Available in 10×38, 14×51, and 22×58 sizes with IEC, UL, and CSA approvals, they feature silver-plated contacts, IP20 touch-safe design, and optional blown fuse indicators — giving panel builders reliable, safe, and flexible protection.
Wayne Moody Joins OEM | Demesne Electrical
We’re excited to share some great news at Demesne Electrical. Wayne Moody has joined our team, bringing with him years of experience and a clear vision for the future. His focus will be on building on our strong reputation here in Ireland and driving our growth across Europe.
PMX Fuse Holder Range – Compact, Reliable, Built for Demanding Panels
The PMX fuse holder range is compact, halogen-free, and manufactured in Europe for fast availability. Available in 10×38, 14×51, and 22×58 sizes with IEC, UL, and CSA approvals, they feature silver-plated contacts, IP20 touch-safe design, and optional blown fuse indicators — giving panel builders reliable, safe, and flexible protection.
Stego Enclosure Heaters with Loop
STEGO’s new loop enclosure heaters are a smart fix for condensation in control cabinets. They heat evenly, install fast with no tools, and come in a range of sizes from 10 to 150 W. They're tough, touch-safe, and even have a built-in thermostat option—everything you need to protect your gear and keep things running smoothly.
